15 Inch Tft 1024x768 Full Viewing Angle Lvds Interface 20 Pins
General Description:
DV150X0M-N10 uses a 12S4P WLED-emitting side-entry light source (bottom) with 50K hours of light source life, including LED driver. It adopts LVDS (1 ch, 8-bit) signal interface with 20 pins total, terminal connection, and 3.3V (Typ.) drive screen voltage. It has a typical vertical refresh rate Fv of 60Hz.
Features:
- LVDS interface with 1 pixel / clock
- High-speed response
- Low color shift image quality
- 6-bit +FRC color depth, display 16.7M colors
- Wide viewing angle
- DE (Data Enable) only mode
- ADS technology is applied for high display quality
- RoHS compliant
Specifications:
| Parameter |
Specification |
Unit |
Remarks |
| Active area |
304. 128(H) × 228.096(V) |
mm |
|
| Number of pixels |
1024(H) × 768(V) |
pixels |
|
| Pixel pitch |
0.297(H) × 0.297(V) |
mm |
|
| Pixel arrangement |
Pixels RGB Vertical stripe |
|
|
| Display colors |
16.7M |
colors |
6bits+FRC |
| Display mode |
Normally Black |
|
|
| Dimensional outline |
326.5(H) × 253.5(V) × 9.7(Total) |
mm |
Detail refer to drawing |
| Weight |
930 |
g |
|
| Power Consumption |
8.72 |
Watt |
Typ. |
| Bezel width (L/R/U/D) |
10/10/11.7/11.7 |
mm |
|
| Surface Treatment |
Haze 25%, 3H |
|
|
| Back-light |
E-LED Light bar Type |
|
|
| LED life |
50000 |
|
|
| Display Direction |
landscape & Portrait |
|
|
Absolute Maximum Ratings:
The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. The operational and non-operational maximum voltage and current values are listed in Table.
| Parameter |
Symbol |
Min. |
Max. |
Unit |
Remark |
| Power Supply Voltage |
VDD |
-0.3 |
4 |
V |
Ta = 25℃ |
| Operating Temperature |
TOP
|
-20 |
+70 |
℃ |
Note 1
|
|
Storage Temperature
|
TSUR
|
-20 |
+70 |
℃ |
|
TST
|
-20 |
+70 |
℃ |
| Operating Ambient Humidity |
Hop |
10 |
90 |
%RH |
| Storage Humidity |
Hst |
10 |
90 |
%RH |
Note 1 : Wet bulb temperature should be 39℃ max. and no condensation of water.
Electrical Specifications:
| Parameter |
Symbol |
Values |
Unit |
Remark |
| Min |
Typ |
Max |
| Power Supply Input Voltage |
VDD |
3.0 |
3.3 |
3.6 |
V |
Note 1 |
| Power Supply Current |
IDD |
- |
410 |
740 |
mA |
| Power Supply Ripple Voltage |
VRP |
- |
- |
300 |
mV |
|
| Rush Current |
IRUSH |
- |
2 |
3 |
A |
Note 2 |
|
LVDS
Interface
|
Differential Input High
Threshold Voltage
|
VLVTH |
-
|
-
|
+100 |
mV |
VLVC=1.2V
|
|
Differential Input Low
Threshold Voltage
|
VLVTL |
- 100 |
-
|
-
|
mV |
| Common Input Voltage |
VLVC |
0.7 |
- |
1.6 |
V |
|
|
CMOS
Interface
|
Input High Threshold
Voltage
|
VIH |
0.7VDD |
-
|
VDD |
V |
|
|
Input Low Threshold
Voltage
|
VIL |
0 |
-
|
0.3VDD |
V |
|
|
Power Consumption
|
PD |
|
0.8 |
1.3 |
W |
|
| PBL |
|
7.92 |
8.71 |
|
Note 3 |
| Ptotal |
|
8.72 |
10.1 |
|
|
Note 1 : The supply voltage is measured and specified at the interface connector of LCM.The current draw and power consumption specified is for VDD=3.3V,Test Pattern of power supply current.
Note 2 : The duration of rush current is about 2ms and rising time of Power Input is 1ms(min).
Note 3 :Calculated value for reference (Input pins*VPIN × IPIN) excluding inverter loss.
Backlight Electrical Specifications:
| Parameter |
Min. |
Typ. |
Max. |
Unit |
Remarks |
| LED Driver Power Supply Voltage |
HVDD |
10.8 |
12 |
12.6 |
V |
|
| LED Driver Power Supply Current |
IHVDD |
550 |
600 |
700 |
mA |
|
|
EN Control Level
|
Backlight on |
VENH
|
3 |
3.3 |
3.6 |
V |
EN logic high
voltage
|
| Backlight off |
VENL
|
0 |
0 |
0.6 |
V |
EN logic low
voltage
|
|
PWM
Control
Level
|
PWM High Level |
VPML
|
3 |
3.3 |
3.6 |
V |
|
| PWM Low Level |
VPML
|
0 |
0 |
0.6 |
V |
|
| PWM Control Frequency |
F PWM |
0.12 |
-
|
20 |
KHz |
Refer to customer comments |
| Duty Ratio |
- |
5 |
- |
100 |
% |
|
| LED Life-Time |
N/A |
50,000 |
- |
- |
Hour |
|
| LED Light Bar Input Voltage Per Input Pin |
VPIN |
32.4 |
36 |
39.6 |
V |
|
| LED Light Bar Input Current Per Input Pin |
IPIN |
-
|
55 |
-
|
mA |
|
| LED Power Consumption |
PBL |
- |
7.92 |
8.71 |
W |
|
Interface Connection:
| Pin No |
Symbol |
Description |
Pin No |
Symbol |
Description |
| 1 |
VDD |
Power Supply, 3.3V(typ.) |
11 |
RIN2- |
-LVDS differential data input 2 |
| 2 |
VDD |
Power Supply,3.3V(typ.) |
12 |
RIN2+ |
+LVDS differential data input 2 |
| 3 |
VSS |
Ground |
13 |
VSS |
Ground |
| 4 |
NC |
No Connection |
14 |
CLKIN- |
-LVDS differential clock input CLK |
| 5 |
RIN0- |
-LVDS differential data input 0 |
15 |
CLKIN+ |
+LVDS differential clock input CLK |
| 6 |
RIN0+ |
+LVDS differential data input 0 |
16 |
VSS |
Ground |
| 7 |
VSS |
Ground |
17 |
RIN3- |
-LVDS differential data input 3 |
| 8 |
RIN1- |
-LVDS differential data input 1 |
18 |
RIN3+ |
+LVDS differential data input 3 |
| 9 |
RIN1+ |
+LVDS differential data input 1 |
19 |
VSS |
Ground |
| 10 |
VSS |
Ground |
20 |
NC |
No Connection |
Optical Specification:
| Parameter |
Symbol |
Condition |
Min |
Typ |
Max |
Unit |
Remark |
|
Viewing
Angle
|
Horizontal |
Θ3 |
CR > 10
|
85 |
89 |
|
Deg. |
Note 1
|
| Θ9 |
85 |
89 |
|
Deg. |
| Vertical |
Θ12 |
85 |
89 |
|
Deg. |
| Θ6 |
85 |
89 |
|
Deg. |
| Brightness |
Lv |
|
315 |
350 |
|
nit |
|
| Uniformity |
9 Points |
ΔY9 |
75% |
80% |
|
|
|
| Contrast ratio |
CR |
Θ = 0.
|
700:1 |
1000:1 |
- |
|
|
|
Reproduction of color
|
White
|
Wx |
Θ = 0.
(Center)
Normal
Viewing
Angle
|
TYP.
- 0.03
|
0.313 |
TYP. + 0.03
|
|
|
| Wy |
0.329 |
|
| Red |
Rx |
0.649 |
|
| Ry |
0.338 |
|
| Green |
Gx |
0.323 |
|
| Gy |
0.627 |
|
| Blue |
Bx |
0.155 |
|
| By |
0.056 |
|
| Color Gamut |
67 |
72 |
- |
% |
| Response Time |
Tr+Tf |
- |
30 |
35 |
ms |
|
| Gamma Scale |
|
|
2.0 |
2.2 |
2.4 |
|
|
Note :
1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are determined for the horizontal or 3, 9 o‟clock direction and the vertical or 6, 12 o‟clock direction with respect to the optical axis which is normal to the LCD surface.
Operating Precautions:
1.Design the length of cable to connect between the connector for back-light and the converter as shorter as possible and the shorter cable shall be connected directly , The long cable between back-light and Converter may cause the Luminance of LED to lower and need a higher startup voltage.
2.The cables should be as short as possible between System Board and PCB interface.
Product Tags:
|
|
20 Pins Lvds TFT Display IPS 1024x768 Full Viewing Angle 89 Degree 15 Inch Images
|
